Being the leaders in the industry, we offer Sattu Plant to our esteemed clients. This plant is installed to product high grade sattu that is consumed by many of the people. It is appreciated for its durability and normal rates. Additionally, this plant is manufactured using superior quality raw material sourced from known and reliable dealers. Some of our products include Commercial Elevator, Reel Machine, Vibro Separator, De-Stoner, Intensive Dampner, Emery Roll, 8 Feed Plantshifter, Pneumetic and Air Lock.
Wheat kernels are scoured between the roll and wire netting and the upper layer of bran is removed from the wheat kernal and polishes the wheat.
VARY ON MATERIAL
15 H.P. / 960 RPM
6' - 3"
2' - 4"
4' - 3"
The Plant Shifter are used manily for shifting, dressing and grading of the ground stock in milling process in each stage of milling process. The Plant Shifter are made in such a flow that in one section, 6 types of graded/shifted stock by way of throughs and the tails with overtails can be taken out at different spouts as needed. The Plant Shifter offered have 8 sections with 16 sieve frame in each section in each Plant Shifter. The Plant Shifter are the shifting media placed in swinging position with accentric osscilating drive. Plant Shifter are made of lighter wood like Pyne wood with square sieve frames therein. Offered Plant Shifter have the square sieve frame of 500mm x 500 mm.
|MODEL||TYPE||SIEVE WIDTH x LENGTH||CAPACITY||DRIVEN BY||MOTOR/' RPM||LENGTH||WIDTH||HEIGHT|
|MPS 816||8 FEED||500mm x500mm x PER SIEVE-FEED||VARY ON MATERIAL||PULLEY||5 HP flange 960 RPM||10-2"||6'||12-6"|
This is the first elevator placed in the shooting pit -about 6' below the ground level in the cleaning section to receive wheat through a chute from the shooting godown to the cleaning section in the mill.
3 H.P 960 R.P.M
1 : 40 Gear Box
12' - 1"
3' - 8"
4' - 7"
5 H.P 960 R.P.M
1 : 40 Gear Box
12' - 1"
4' - 2"
5' - 2"
These are other machine in the pre-cleaning and cleaning section to remove impurities by sizes having 2 nets and fitted with 2 nos. Vibro motors at both side of the body frame and mounted on the plate with the body of machine to adjust the stroke as per requirement.The 1st net is of 6.5 mm - 6mm/6mm - 5.5 mm / 5.5mm - 5mm to allow wheat and smaller impurities but to separate the bigger/longer impurities over the net and the 2nd net is of 2.5 mm triangular perforation separating wheat with a little bit impurities over 2.5mm size but allow to pass small impurities for separation. This separator is attached with an Aspiration channel and the so cleaned wheat is coming to the hopper of the aspiration channel over a magnetic rod in a wide stream to effect the separation of ferrous material in the flow if any remain with the wheat.The aspiration channel is joined with an air duct line of 200 mm dia to aspire by an air flow at a low pressure to collect the fine and dusty impurities from the wheat flow.
|MODEL i CAPACITY||MOTOR/ RPM||DRIVEN BY||LENGTH||WIDTH||HEIGHT|
|MVS 1000 I 8 T/Hr.||0.75 H.Px2 960 R.PM||VIBRO MOTOR||9'-2"||4'-9"||5--3"|
|MVS 1200 ' 12 T/Hr.||1 H.Px2 960 R.PM||VIBRO MOTOR||9-2"||5-6"||5'-3"|
Stones of same sizes of wheat kernel are separated by the principal of gravity classification which connected with another aspiration line where are again separating light impurities from the wheat.
|MODEL||CAPACITY||MOTOR/' RPM||DRIVEN BY||LENGTH||WIDTH||HEIGHT|
|MDS 750||6 T/Hr.||0.75 HP 960 R.PM||VIBRO MOTOR||5'-r||3-6"||5'-4"|
|MDS 1200||10 T/Hr. -||.75 H.PX2 960 R.PM||VIBRO MOTOR||5'-r||4'-6"||5'-4"|
This is a machine specially for addition moisture with scouring effect on the wheat kernel working on high speed like scourer for faster and better penetration of water in wheat kernel.
This machine is used where high pressure is required and is presented at the best rates in the market. It is fabricated using latest technology machineries to meet the international quality standards. There are various models available of this machine that differs in their size and capacity. Also, it is an export quality and can be availed in normal rates.: This is compact system for conveying the milled stock to different feeds of planshifters and/or other machines as required .
This system comprises of the followings:
Receiving hoppers ( Feeders)
Lift Seamless / ERW Pipes of required dia with wall thickness of app. 3.5mm to 4.5 mm.
Lift bends with smooth radius as required mainly of 1000 mm made of the same pipe as of life pipe.
Small pneumatic cyclones ( Soild & Air separator)
The Jet filter offered is designed and made in a manner to match with the outflow of the HP Fan.
its key advantages are: